Attwood 238 Series Seat Mounts Bedienungsanleitung PDF herunterladen

Figure 4

Figure 5

Figure 3

Figure 2

2. On slider platform, slide handle must be beneath front of seat. Adjust slider platform

fore/aft so that front edge is even with front of seat. Handle will be slightly exposed.

3. Insert 1/4"-20 stainless steel machine screws through washers and the widest pat-

tern that matches T-nuts in bottom of seat.

Be sure at least 3/8" (8mm) thread length enters the seat’s T-nuts.

4. If seat does not have T-nuts, it must be securely thru-bolted with 1/4" stainless

bolts, washers and nuts.

5. When seat is fastened reinsert into the pedestal tube and press all the way down.

Check for pivot, slide, and locking operations.

MAINTENANCE

1. Clean pedestal and mount with mild soap and water. Do not use abrasive

cleansers or polishing agents.

2. Periodically check all fasteners for proper tightness.

2. For Socket bases only: drill 3-1/2" deep x 3-1/4" dia. (89 x 89mm) hole at exact

center of mounting location.

3. For Square and D-Shape Socket bases: remove one plastic knockout so correct

slot is open for forward locking position.

4. Turn base so pedestal tube slot is opposite the Auto Lock handle side.

5. Use base as template to mark and drill 5/16" (8mm) holes through deck and substrate.

6. Thru-bolt the base with stainless steel 1/4"-20 countersunk-head machine screws,

washers, and nuts.

FASTEN SEAT TO PEDESTAL

1. Place seat mount or slider platform against bottom of the seat. (Figure 5)

MATERIALS REQUIRED FOR INSTALLATION

• Six (6) 1/4"-20 stainless countersunk-head machine screws, washers and nuts.

Bolts must be suitable length for mounting location and substrate.

NOTE: Do not use copper or copper-plated fasteners.

• Four (4) 1/4"-20 stainless steel machine screws and washers to attach seat to mount.

MOUNTING LOCATION AND HEIGHT

• Best sitting height (including seat) is about 15-1/2" (39cm) above deck.

• Pedestal must be mounted to a suitable marine-grade substrate according to

ABYC standards.

• Aluminum or stainless steel backing plate is also recommended.

PEDESTAL BASE INSTALLATION INSTRUCTIONS

1. Lift Auto Lock handle to unlock the seat mount; remove it from pedestal tube.

IMPORTANT: Pedestal base orientation determines the correct direction of the seat

tilt and Auto Lock handle. Before fastening, the base slot must be positioned on the

side

opposite the Auto Lock Handle (Figure 4).

To Operate Slider Platform Handle:

1. Lift handle to allow fore-aft motion. (Figure 2)

2. Release handle to hold slider in place. Fully lock by pushing handle down.

To Remove / Relocate Pedestal Tube from Socket Base:

1. To insert pedestal tube: Align Locking Latch with Base Slot. Press down until the

latch locks. Try to lift tube to be certain it is locked in place. (Figure 3)

2. To remove pedestal tube: Depress button at bottom of tube. Twist and lift to

remove tube.

To Operate Auto Lock Handle:

1. Lift Auto Lock handle to unlock and pivot.

2. When you release handle, seat will automatically lock forward as you rotate to

forward position (Figure 2).

NOTE: Seat must be locked forward when vessel is in motion.

Figure 1

PEDESTAL FEATURES

Swivl-Eze 238 Series Pedestals offer ergonomic controls and smooth, wobble-free

motion. They meet Type A Driver ABYC H-31 regulations for driver’s seat applications.

Installers and users must abide by all ABYC and U.S. Coast Guard regulations for seating.

Pedestal is ordered with Auto Lock handle at Left, Right, or (on Seat Mount versions)

Forward. Handle can’t be modified to a different orientation.

HOW TO USE THE PEDESTAL

WARNING

According to ABYC and Coast Guard regulations, when the vessel is in motion, seat

must face forward with Auto Lock handle engaged (Figure 1).

SAVE THESE INSTRUCTIONS

Form Number 69400 Rev. B 04-04

238 Series 2-3/8" Diameter

Bell and Socket Pedestals

Installation Instructions

Boat Front

Lift Lever Up:

Rotation Unlocked

Release Lever:

Rotation Will

Auto Lock In

Forward Position

Boat Rear

Locked

Auto Lock

Handle

Fore-Aft Slide Handle

UnLocked

Button

Locking

Latch

Base

Slot

Pedestal Slot

Handle Always

Opposite Slot

13-7/8"

12"

9-1/4"

(.75" x .38")

4-Holes

(.57" x .32")

4-Holes

(.75" x .32") 4-Holes

1/4"-20 Bolts

Thru-bolted

to Substrate

Slot On Side

Opposite Handle

Base

Slot

Base

Slot

Bell and Socket Pedestals 1

Inhaltsverzeichnis

Seite 1 - Bell and Socket Pedestals

Figure 4Figure 5Figure 3Figure 22. On slider platform, slide handle must be beneath front of seat. Adjust slider platformfore/aft so that front edge i

Kommentare zu diesen Handbüchern

Keine Kommentare

Attwood 238 Series Seat Mounts Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Attwood 238 Series Seat Mounts herunter. Attwood 238 Series Seat Mounts User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Attwood 238 Series Seat Mounts